This is a library of perfboard and single-sided PCB effect layouts for guitar and bass. I'm not an electrical engineer by any stretch of the imagination, just a DIY'er who likes drawing layouts. It is meant for the hobbyist (so commercial use of any of these layout is not allowed without permission) and as a way to give back to the online DIY community.

Monday, June 20, 2016

Catalinbread SFT

Here's a really versatile overdrive from Catalinbread. The SFT is based on Ampeg amps from the 70s, using JFETs to simulate tubes (like many of Catalinbread's other overdrives). The Stones/Stoner switch allows you to go from verge of breakup tones to near fuzz tones with the flip of a switch. This can be run off 18 volts and this gives extra headroom, so it may not be a bad idea to include a charge pump in your build. This layout reflects the newest version of the SFT, and the schematic can be found here.


34 comments:

  1. 18v really brings this one alive

    ReplyDelete
  2. Hello,

    Please make PCB for Catalinbread DLS MKIII

    reg
    Martin

    ReplyDelete
  3. The 33k resistor should be 2k2

    ReplyDelete
  4. Verified! I went with J201 for the trannies, a single 2n4393 costs like four pounds here. Also tried with 2n5458 but those made the breakup nasty and sputtery and a bit gated. Now it is really gainy, wonder how it sounds with a set of 2n5457. I wired the switch as the tagboardfx-layout suggests: lug 2 & 3 goes to bottom, and lug 5 & 6 to the top holes.
    Thanks for the layout!

    ReplyDelete
    Replies
    1. I got my 2n4393s on Aliexpress for less. Didnt use them in my build yet, so i dont know how they compare to j201.

      The tagboardfx uses a differend numbering for the switch imho.

      Delete
  5. Cool, thanks! Is there any tranny/combination that you prefer?

    ReplyDelete
  6. Hello I had a problem with mine on the stones mode i have a really low gain and volume and when i switch to stoner everything seems like the video. I cheked every value and everything seems correct , the trannies i used are KS4393 which only have different layout from the stock ones. Is there a way i can boost the stones mode a little bit? Thanks in advance

    ReplyDelete
  7. Hello. If a want only use the stoner mode, should put some jumper in the place of swithches? Thanks

    ReplyDelete
    Replies
    1. Just jump the Sw2-3 pads and leave the Sw4-5 pads open. You can also omit the 470k and 4.7n right by the Sw4-5 pads.

      Delete
    2. Nooby cuestión, but thankss

      Delete
    3. Hi there
      May I ask a similar question please? If I like to go Stones mode only, how should I jump? Jump sw3 and 4?

      Delete
    4. For Stones only, jump pads sw4-5 and leave sw2-3 open. Then you can omit the 22uF cap in the top right of the board as well.

      Delete

  8. Do you think i can build it with the transistor replacement mpf4393 by mpf102?

    ReplyDelete
    Replies
    1. Compare the datasheets, but I think that should work. Worth socketing and experimenting with at least. J201 will work here and I would guess 2N5457s would too.

      Delete
  9. This comment has been removed by the author.

    ReplyDelete
  10. I see in the picture Sw2 and Sw3.. And Sw4 and Sw5.
    And i See that in the original Pedal has only 1 Stoner Button
    How is it? Shoud i Jumper one of the two Sw?
    Sory for my english

    ReplyDelete
    Replies
    1. Those are the pin numbers for a double pole double throw (DPDT) switch. 4 and 5 are connected for "Stones" and 2 and 3 for "Stoner". All unconnected is closer to the "Stoner" side, but slightly less gain and volume. The switch is not necessary for the circuit to work.

      Delete
  11. Verified!! Sounds huge and has a wonderful ampeg character. The fuzz side is a beast. Used 2N5457. Will try another one with J201, but I think it will be almost the same. Thanks again for your work here!!
    Pic here:
    http://www.studionegro.tv/ftp/diy/sft2.jpg

    ReplyDelete
  12. I'm pretty sure the 470K on the input is on the wrong side of the 100nF cap at the input. (R1 and C1 on the schematic that comes up when you search for it). It will work, but if you boost the signal going into the pedal up above 2VAC it will throw Q1 out of whack and be a sputtering fuzz mess until the voltage settles back down. I just added an additional 470K on the solder side of the board because it's a PITA to pull out and monkey around with, and that solved my problem I was having with it. Cheers.

    ReplyDelete
    Replies
    1. Hi! I know it's been a while, but can you explain me better where did you solder that aditional 470k res? Just after the Input, before splits into cap and the other res? I've been experiencing the same problem, mostly in Stoner mode, and with all transistors (2N5457, J201 & BF245A). Thanks in advance. Regards

      Delete
  13. Hi, I saw a Ampeg based kit called Ampegulator (fuzzdog pedal parts) using a charge pump to provide 18V DC by using an external switch, is it what does the stones/stoner control of the SFT v2 ?

    ReplyDelete
    Replies
    1. The switch on the SFT v2 changes some component values in the circuit. The Ampegulator just adds a switchable charge pump, giving you the option to run at 9v or 18v.

      Delete
    2. OK so thé ampegulator is a kind of sft v1....!?

      Delete
    3. Thanks for answering, what about the 18v on the present layout ? is a mod needed to use it with 18V (add of a charge pump pcb) ? regards
      PS: does the layout takes in account revisions suggested by the comments about JFETs or component values ?

      Delete
    4. You can add a charge pump board to your build. As long as your components are rated high enough you shouldn't have any problems. (Really it's electrolytic caps you have to worry about. I generally don't buy any rated at less than 35v)

      It's been a while since I worked on this layout, but it is verified and follows the schematic linked in the description.

      Delete
  14. I may be wrong but I think the transfer layout has not been inverted ?

    ReplyDelete
    Replies
    1. For the typical tone transfer method it doesn't need to be inverted. If you're using the photo resist method you can invert it before printing, but since you're likely to be printing on transparency you can just flip the print out over and be fine.

      Delete
  15. This comment has been removed by the author.

    ReplyDelete
    Replies
    1. What's the dpdt Pinot for the stones/stoner switch?
      1-2
      3-4
      5-6

      Or

      1-4
      2-5
      3-6

      Delete
    2. Nevermind, found it on fsb

      Delete
    3. Btw some put put a 1Mohm between the gate of Q1 and ground to stabilize bias of Q1 and have some good result if other jfets are used . And even with some brand of MPF4393. For info on this , stoner mode oscillation problem and later catalinbread values for some resistors, google Aion Artemis mk.II v1.1 pdf and you'll find what you're looking for.

      Delete